写点什么

全网最牛逼的华为信息中心配置命令,建议收藏!

作者:Ethereal
  • 2021 年 12 月 19 日
  • 本文字数:29331 字

    阅读完需:约 96 分钟

本文命令集合:


  • display actived-alarm highest-level

  • display channel

  • display debugging

  • display info-center

  • display info-center filter-id

  • display info-center logfile path

  • display info-center rate-limit record

  • display info-center rate-limit threshold

  • display info-center statistics

  • display log

  • display logbuffer

  • display logfile

  • display trapbuffer

  • info-center channel

  • info-center channel name

  • info-center enable

  • info-center filter-id

  • info-center logbuffer

  • info-center logbuffer size

  • info-center logfile path

  • info-center logfile size

  • info-center loghost

  • info-center loghost source

  • info-center max-logfile-number

  • info-center rate-limit except

  • info-center rate-limit global-threshold

  • info-center rate-limit monitor-period

  • info-center rate-limit threshold

  • info-center source channel

  • info-center statistic-suppress enable

  • info-center timestamp

  • info-center trapbuffer

  • info-center trapbuffer size

  • reset info-center statistics

  • reset logbuffer

  • reset trapbuffer

  • save logfile

  • terminal debugging

  • terminal logging

  • terminal monitor

  • terminal trapping


下面详细介绍:

display actived-alarm highest-level

命令功能

display actived-alarm highest-level 用来查看当前活动告警的最高告警级别。

命令格式

display actived-alarm highest-level
复制代码

使用实例

查看当前活动告警的最高告警级别。


<Huawei> display actived-alarm highest-level Info: The highest level of active alarm is critical.
复制代码

display channel

命令功能

display channel 命令用来查看设备信息中心的信息通道的配置信息。

命令格式

display channel [ channel-number | channel-name ]
复制代码

使用实例

查看 0 号信息通道的配置信息。


<Huawei> display channel 0channel number: 0, channel name: console                                        MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      warning       Y      debugging     Y      debugging    
复制代码


查看设备所有信息通道的配置信息。


<Huawei> display channelchannel number: 0, channel name: console                                        MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      warning       Y      debugging     Y      debugging                                                                                    channel number: 1, channel name: monitor                                        MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      warning       Y      debugging     Y      debugging                                                                                    channel number: 2, channel name: loghost                                        MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      informational Y      debugging     N      debugging                                                                                    channel number: 3, channel name: trapbuffer                                     MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  N      informational Y      debugging     N      debugging                                                                                    channel number: 4, channel name: logbuffer                                      MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      warning       N      debugging     N      debugging                                                                                    channel number: 5, channel name: snmpagent                                      MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  N      debugging     Y      debugging     N      debugging                                                                                    channel number: 6, channel name: channel6                                       MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      debugging     Y      debugging     N      debugging                                                                                    channel number: 7, channel name: channel7                                       MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      debugging     Y      debugging     N      debugging                                                                                    channel number: 8, channel name: channel8                                       MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      debugging     Y      debugging     N      debugging                                                                                    channel number: 9, channel name: channel9                                       MODU_ID  NAME     ENABLE LOG_LEVEL     ENABLE TRAP_LEVEL    ENABLE DEBUG_LEVEL  ffff0000 default  Y      debugging     Y      debugging     N      debugging    
复制代码


display debugging

命令功能

display debugging 命令用来查看设备允许发送的调试信息。

命令格式

display debugging [ interface interface-type interface-number ] [ module-name ]
复制代码

使用实例

查看设备允许发送的调试信息。


<Huawei> display debuggingACL error debugging is on, on the slot 0
复制代码


查看设备 ARP 模块允许发送的调试信息。


<Huawei> display debugging arpslot[0]:ARP packet debugging is on    
复制代码

display info-center

命令功能

display info-center 命令用来查看信息中心输出方向的配置信息。

命令格式

display info-center
复制代码

使用实例

查看信息中心输出方向的配置信息。


<Huawei> display info-centerInformation Center: enabledLog host:                                                                               10.1.1.1, channel number: 2, channel name: loghost                              language: english, host facility: local7   Console:        channel number: 0, channel name: consoleMonitor:        channel number: 1, channel name: monitorSNMP Agent:        channel number: 5, channel name: snmpagentLog buffer:        enabled        max buffer size: 1024, current buffer size: 512        current messages: 6, channel number: 4, channel name: logbuffer        dropped messages: 0, overwritten messages: 0Trap buffer:        enabled        max buffer size: 1024, current buffer size: 256        current messages: 0, channel number: 3, channel name: trapbuffer        dropped messages: 0, overwritten messages: 0Logfile:        channel number: 9, channel name: channel9, language: EnglishInformation timestamp setting:        log - date, trap - date, debug - date
Sent messages = 25, Received messages = 25
复制代码


display info-center filter-id

命令功能

display info-center filter-id 命令用来查看信息中心过滤的信息。

命令格式

display info-center filter-id [ id | bymodule-alias modname alias ]
复制代码

使用实例

查看过滤表中 ID 为 3246215177 的过滤信息。


<Huawei> display info-center filter-id 3246215177  ID              : 3246215177                                                    Module          : 6OVER4                                                        Alias           : DEL_UPTUNN_FAIL                                               Content         : Failed to delete the UPTUNNEL entry when processing ([STRING]). (Interface=[STRING])                                                          Filtered Number : 0           
复制代码


查看过滤表中所有的 ID 信息。


<Huawei> display info-center filter-idID              : 3246215177                                                    Module          : 6OVER4                                                        Alias           : DEL_UPTUNN_FAIL                                               Content         : Failed to delete the UPTUNNEL entry when processing ([STRING]). (Interface=[STRING])                                                          Filtered Number : 0                                                                                                                                             ID              : 3491254537                                                    Module          : BGP                                                           Alias           : ADD_DELETED_ROUTE                                             Content         : Add the route [STRING] that have other flags besides deleted flag [USHORT]                                                                    Filtered Number : 0   
复制代码


display info-center logfile path

命令功能

display info-center logfile path 命令用来查看日志文件保存的路径。

命令格式

display info-center logfile path               
复制代码

使用实例

查看日志文件保存的路径。


<Huawei> display info-center logfile pathInfo: Logfile save path is usb0:/logfile
复制代码

display info-center rate-limit record

命令功能

display info-center rate-limit record 命令用来查看信息中心日志速率抑制情况。

命令格式

display info-center rate-limit record
复制代码

使用实例

查看信息中心日志速率抑制情况。


<Huawei> display info-center rate-limit record Record No.1 InfoID               : ff5ad009 Module               : AAA Alias                : DESTFAILAUTHEN_ERR_EVENT Rate limit threshold : 50 Total receive number : 1872 Total drop number    : 922 Total send number    : 950 Begin timestamp      : 2014-11-18 11:41:28
复制代码


display info-center rate-limit threshold

命令功能

display info-center rate-limit threshold 命令用来查看信息中心日志速率抑制的阈值。阈值信息包括系统中跟随版本发布的缺省阈值、特殊 ID 的缺省阈值和系统启动后用户通过命令配置的阈值。

命令格式

display info-center rate-limit threshold
复制代码

使用实例

查看信息中心配置的阈值


<Huawei> display info-center rate-limit threshold Rate limit threshold(per second): Module           Alias                                   Default  Config        default                                                  30       30            IPC              IPCFRGTOOLARGE                          5        5             IPC              IPCDUMPMEM                              5        5             IPC              ALLOCINDEXERR                           5        5             IPC              DRVNOTSTABLE                            2        2             IPC              NOTIMODFALNOREASM                       2        2             IPC              SYNRPCGETSMFAL                          5        5             IPC              SYNRPCMODUNREG                          5        5             IPC              SYNRPCRETNULL                           5        5             IPC              MODULENOTREG                            5        5             IPC              SENDRETURN                              5        5             IPC              GETMTUFAL                               5        5             IPC              ALLOCIPCFRGFAL                          5        5             IPC              RECVINVALIDMSG                          5        5             IPC              RCVNOTIQUEERR                           5        5             IPC              NOTIFYQUEERR                            5        5             IPC              SENDFINISHRETURN                        5        5             IPC              RECVINVALIDMSGTYPE                      5        5             SOURCE           UMSGGETSRCOBJFAL                        1        1       
复制代码


display info-center statistics

命令功能

display info-center statistics 命令用来查看信息中心的统计信息。

命令格式

display info-center statistics
复制代码

使用实例

查看信息中心的统计信息。


<Huawei> display info-center statisticsInformation statistics data:ModuleID   ModuleName      LogNumber  DiagLogNumber   TrapNumber  DebugNumberc17d0000   6OVER4          0          0               0           0ff5a0000   AAA             0          0               0           0c06c0000   ACL             0          0               0           0c0ef0000   ACL6            0          0               0           0ff1e0000   ACLE            0          0               0           0ff8e0000   ADA_BFD         0          0               0           0c0e70000   ADDR            0          0               0           0ff740000   ADP-ACL         0          0               0           0ff730000   ADP-IPSEC       0          0               0           0ff120000   ADP_MSTP        11         0               0           0ff2c0000   ADPIPV4         0          7               0           0ff950000   ADPIPV6MB       0          0               0           0ff5d0000   AM              0          0               0           0ffff0000   AMPADP          0          0               0           0c1a80000   ANTIATTACK      0          0               0           0c16e0000   ARP             0          0               0           771c1860000   ARP-PING        0          0               0           0c19d0000   ARPLINK         0          0               0           0c0cf0000   ATM             0          0               0           0             
复制代码


display log

命令功能

display log 命令用来查看用户的操作记录。

命令格式

display log [ cli | snmp ] index index1 [ index2 ]
display log [ cli | snmp ] { all | name username } [ start-date [ start-time [ – end-date [ end-time ] ] ] ]
复制代码

使用实例

查询日志序号从 10 到 15 的记录。


<Huawei> display log index 10 15  ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address             15                                    --                10.138.78.127          Time: 2007-08-25 18:00:43+00:00                                                 Cmd:  traffic classifier cy                                                     ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address             14                                    --                10.138.78.127          Time: 2007-08-25 17:59:51+00:00                                                 Cmd:  undo traffic behavior cy                                                  ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address             13                                    --                10.138.78.127          Time: 2007-08-25 17:59:42+00:00                                                 Cmd:  undo traffic policy cy                                                    ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address             12                                    --                10.138.78.127          Time: 2007-08-25 17:55:26+00:00                                                 Cmd:  quit                                                                      ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address             11                                    --                10.138.78.127          Time: 2007-08-25 17:54:05+00:00                                                 Cmd:  undo classifier cy                                                        No.   UserName                          Domain            IP-Address             10                                    --                10.138.78.127          Time: 2007-08-25 17:54:05+00:00                                                 Cmd:  traffic policy cy                                                         ---------------------------------------------------------------------------   
复制代码


查询所有用户在一个时间段内的日志信息,起始日期为 2007-08-25,起始时间为 17:10:10,结束日期为 2007-08-25,结束时间为 17:20:10。


<Huawei> display log all 2007-08-25 17:10:10 - 2007-08-25 17:20:10    ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              78                                    --                10.138.78.127         Time: 2007-08-25 17:19:59+00:00                                                 Cmd:  stp enable                         7                                       ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              77                                    --                10.138.78.127         Time: 2007-08-25 17:19:47+00:00                                                 Cmd:  stp pathcost-standard legacy                                              ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              76                                    --                10.138.78.127         Time: 2007-08-25 17:19:35+00:00                                                 Cmd:  stp root primary                                                          ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              75                                    --                10.138.78.127         Time: 2007-08-25 17:19:04+00:00                                                 Cmd:  log off                                                                   ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              74                                    --                10.138.78.127         Time: 2007-08-25 17:18:54+00:00                                                 Cmd:  system-view                                                               ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              73                                    --                10.138.78.127         Time: 2007-08-25 17:18:49+00:00                                                 Cmd:  log on                                                                    ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              72                                    --                10.138.78.127         Time: 2007-08-25 17:18:17+00:00                                                 Cmd:  stp root primary                                                          ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              71                                    --                10.138.78.128         Time: 2007-08-25 17:18:13+00:00                                                 Cmd:  info-center snmp channel snmpagent                                        ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              70                                    --                10.138.78.127         Time: 2007-08-25 17:18:04+00:00                                                 Cmd:  stp mode stp                                                              ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              69                                    --                10.138.78.127         Time: 2007-08-25 17:17:58+00:00                                                 Cmd:  system-view                                                               ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              68                                    --                10.138.78.127         Time: 2007-08-25 17:17:35+00:00                                                 Cmd:  log on                                                                    ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              67                                    --                10.138.78.128         Time: 2007-08-25 17:17:31+00:00                                                 Cmd:  info-center monitor channel monitor                                       ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              66                                    --                10.138.78.128         Time: 2007-08-25 17:15:37+00:00                                                 Cmd:  info-center loghost source Ethernet 0/0/1                                 ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              65                                    --                10.138.78.128         Time: 2007-08-25 17:13:04+00:00                                                 Cmd:  info-center loghost 10.1.1.2 language English                             ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              64                                    --                10.138.78.128         Time: 2007-08-25 17:11:55+00:00                                                 Cmd:  system-view                                                               ---------------------------------------------------------------------------     No.   UserName                          Domain            IP-Address              63                                    --                10.138.78.128         Time: 2007-08-25 17:11:53+00:00                                                 Cmd:  log on                                                                    ---------------------------------------------------------------------------   
复制代码


display logbuffer

命令功能

display logbuffer 命令用来查看 Log 缓冲区记录的信息。

命令格式

display logbuffer [ size size | module module-name | level severity ] *
display logbuffer summary [ level severity ]
display logbuffer log-offset offset-value size size
复制代码

使用实例

查看 Log 缓冲区的所有日志信息。


<Huawei> display logbufferLogging buffer configuration and contents: enabled                              Allowed max buffer size: 1024                                                   Actual buffer size: 512                                                         Channel number: 4, Channel name: logbuffer                                      Dropped messages: 0                                                             Overwritten messages: 167                                                       Current messages: 512                                                                                                                                           May 10 2012 13:42:59+00:00 huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[0]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=912)                                                                           May 10 2012 13:32:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[1]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 13:22:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[2]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 13:12:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[3]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=912)                                                                           May 10 2012 13:02:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[4]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 12:52:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[5]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 12:42:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[6]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=912)                                                                           May 10 2012 12:32:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[7]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 12:22:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[8]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 12:12:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[9]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=912)                                                                           May 10 2012 12:02:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[10]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                          May 10 2012 11:52:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[11]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                          May 10 2012 11:42:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[12]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=912)                                                                          May 10 2012 11:32:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[13]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                          May 10 2012 11:22:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[14]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                          May 10 2012 11:12:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[15]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                          May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[16]:Interface Ethernet5/0/2 has turned into UP state.                                     May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[17]:Interface Ethernet5/0/1 has turned into UP state.                                     May 10 2012 11:08:37+00:00 Huawei %%01IFNET/4/LINK_STATE(l)[18]:The line protocol IP on the interface Vlanif20 has entered the UP state.            May 10 2012 11:08:37+00:00 Huawei %%01IFNET/4/IF_STATE(l)[19]:Interface Vlanif20 has turned into UP state.                                          May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[20]:Interface Ethernet5/0/0 has turned into UP state.                                     May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[21]:Interface GigabitEthernet5/0/0 has been available.                                   May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[22]:Interface Ethernet5/0/7 has been available.                                          May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[23]:Interface Ethernet5/0/6 has been available.              
复制代码



查看概要的日志缓冲区的日志信息。


<Huawei> display logbuffer summary EMERG ALERT  CRIT ERROR  WARN NOTIF  INFO DEBUG                                     0     0     0    14   498     0     0     0    
复制代码



查看日志缓冲区中偏移前 15 条日志后的 10 条日志,即从第 16 条日志开始的 10 条日志。


<Huawei> display logbuffer log-offset 15 size 10Logging buffer configuration and contents: enabled                              Allowed max buffer size: 1024                                                   Actual buffer size: 512                                                         Channel number: 4, Channel name: logbuffer                                      Dropped messages: 0                                                             Overwritten messages: 168                                                       Current messages: 512                                                                                                                                           May 10 2012 11:12:59+00:00 Huawei %%01DEFD/4/CPCAR_DROP_MPU(l)[0]:Some packets are dropped by cpcar on the MPU. (Packet-type=arp-request, Drop-Count=684)                                                                           May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[1]:Interface Ethernet5/0/2 has turned into UP state.                                      May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[2]:Interface Ethernet5/0/1 has turned into UP state.                                      May 10 2012 11:08:37+00:00 Huawei %%01IFNET/4/LINK_STATE(l)[3]:The line protocol IP on the interface Vlanif20 has entered the UP state.             May 10 2012 11:08:37+00:00 Huawei %%01IFNET/4/IF_STATE(l)[4]:Interface Vlanif20 has turned into UP state.                                           May 10 2012 11:08:37+00:00 Huawei %%01IFPDT/4/IF_STATE(l)[5]:Interface Ethernet5/0/0 has turned into UP state.                                      May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[6]:Interface GigabitEthernet5/0/0 has been available.                                    May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[7]:Interface Ethernet5/0/7 has been available.                                           May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[8]:Interface Ethernet5/0/6 has been available.                                           May 10 2012 11:08:34+00:00 Huawei %%01IFNET/4/IF_ENABLE(l)[9]:Interface Ethernet5/0/5 has been available.       
复制代码

display logfile

命令功能

display logfile 命令用来查看日志文件信息。

命令格式

display logfile file-name [ offset | hex ] *
复制代码

使用实例

显示指定路径的日志文件中保存的日志信息。


<Huawei> display logfile usb0:/logfile/log.log                                                                                                                                                                ################################################################                #     This logfile is generated at slot 0                                       ################################################################                                                                                                Apr 23 2011 11:06:51+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                                                            Apr 23 2011 11:06:51+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3487]:Interface Ethernet0/0/1 has turned into DOWN state.                                 Apr 23 2011 11:06:53+00:00 huawei IFNET/6/IF_PVCUP:OID 1.3.6.1.6.3.1.1.5.4 Interface 6 turned into UP state.(AdminStatus 1,OperStatus 1,InterfaceName Ethernet0/0/1)                                                                Apr 23 2011 11:06:53+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3488]:Interface Ethernet0/0/1 has turned into UP state.                                   Apr 23 2011 11:06:53+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                                                            Apr 23 2011 11:06:53+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3489]:Interface Ethernet0/0/1 has turned into DOWN state.                                 Apr 23 2011 11:06:55+00:00 huawei IFNET/6/IF_PVCUP:OID 1.3.6.1.6.3.1.1.5.4 Interface 6 turned into UP state.(AdminStatus 1,OperStatus 1,InterfaceName Ethernet0/0/1)                                                                Apr 23 2011 11:06:55+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3490]:Interface Ethernet0/0/1 has turned into UP state.                                   Apr 23 2011 11:06:56+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                                                            Apr 23 2011 11:06:56+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3491]:Interface Ethernet0/0/1 has turned into DOWN state.                                 Apr 23 2011 11:06:58+00:00 huawei IFNET/6/IF_PVCUP:OID 1.3.6.1.6.3.1.1.5.4 Interface 6 turned into UP state.(AdminStatus 1,OperStatus 1,InterfaceName Ethernet0/0/1)                                                                Apr 23 2011 11:06:58+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3492]:Interface Ethernet0/0/1 has turned into UP state.                                   Apr 23 2011 11:06:59+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                                                            Apr 23 2011 11:06:59+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3493]:Interface Ethernet0/0/1 has turned into DOWN state.                                 Apr 23 2011 11:07:00+00:00 huawei IFNET/6/IF_PVCUP:OID 1.3.6.1.6.3.1.1.5.4 Interface 6 turned into UP state.(AdminStatus 1,OperStatus 1,InterfaceName Ethernet0/0/1)                                                                Apr 23 2011 11:07:00+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3494]:Interface Ethernet0/0/1 has turned into UP state.                                   Apr 23 2011 11:07:01+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                                                            Apr 23 2011 11:07:01+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3495]:Interface Ethernet0/0/1 has turned into DOWN state.                                 Apr 23 2011 11:07:03+00:00 huawei IFNET/6/IF_PVCUP:OID 1.3.6.1.6.3.1.1.5.4 Interface 6 turned into UP state.(AdminStatus 1,OperStatus 1,InterfaceName Ethernet0/0/1)                                                                Apr 23 2011 11:07:03+00:00 huawei %%01IFPDT/4/IF_STATE(l)[3496]:Interface Ethernet0/0/1 has turned into UP state.                                   Apr 23 2011 11:07:03+00:00 huawei IFNET/1/IF_PVCDOWN:OID 1.3.6.1.6.3.1.1.5.3 Interface 6 turned into DOWN state.(AdminStatus 1,OperStatus 2,InterfaceName Ethernet0/0/1)                               
复制代码


以 16 进制形式显示日志文件中保存的日志信息。


<Huawei> display logfile usb0:/logfile/log.log hex       0d  0a  0d  0a  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  0d  0a  23  20  20  20  20  20  54  68  69  73  20  6c  6f  67  66  69  6c  65  20  69  73  20  67  65  6e  65  72  61  74  65  64  20  61  74  20  73  6c  6f  74  20  30  0d  0a  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  23  0d  0a  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  
复制代码

display trapbuffer

命令功能

display trapbuffer 命令用来查看信息中心 Trap 缓冲区记录的信息。

命令格式

display trapbuffer [ size value ]
复制代码

使用实例

查看 Trap 缓冲区记录的所有信息。


<Huawei> display trapbufferTrapping buffer configuration and contents: enabled                             Allowed max buffer size: 1024                                                   Actual buffer size: 256                                                         Channel number: 3, Channel name: trapbuffer                                     Dropped messages: 0                                                             Overwritten messages: 0                                                         Current messages: 29                                                                                                                                            #Sep 17 2012 17:09:47+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 17 2012 17:06:50+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=0, LldpStatsRemTablesDeletes=1, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 20:03:40+00:00 huawei ENTITYTRAP/4/CPUUSAGERESUME:OID 1.3.6.1.4.1.2011.5.25.219.2.14.2 CPU utilization resumed from exceeding the pre-alarm threshold.(Index=9, HwEntityThresholdIndex=0, HwEntityPhysicalIndex=9, PhysicalName="SRU Board 0", EntityThresholdType=1, EntityThresholdWarning=80, EntityThresholdCurrent=23, EntityTrapFaultID=144896)                                              #Sep 14 2012 18:15:27+00:00 huawei LLDP/4/ADDCHGTRAP:OID: 1.3.6.1.4.1.2011.5.25.134.2.5 Local management address is changed. (LocManIPAddr=1.1.1.9)             #Sep 14 2012 18:13:40+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 18:13:23+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=0, LldpStatsRemTablesDeletes=1, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 17:16:05+00:00 huawei ENTITYTRAP/4/CPUUSAGERESUME:OID 1.3.6.1.4.1.2011.5.25.219.2.14.2 CPU utilization resumed from exceeding the pre-alarm threshold.(Index=9, HwEntityThresholdIndex=0, HwEntityPhysicalIndex=9, PhysicalName="SRU Board 0", EntityThresholdType=1, EntityThresholdWarning=80, EntityThresholdCurrent=9, EntityTrapFaultID=144896)                                               #Sep 14 2012 17:15:37+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 17:15:37+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 17:15:34+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 17:15:33+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)              #Sep 14 2012 17:15:33+00:00 huawei LLDP/4/NBRCHGTRAP:OID: 1.0.8802.1.1.2.0.0.1 Neighbor information is changed. (LldpStatsRemTablesInserts=1, LldpStatsRemTablesDeletes=0, LldpStatsRemTablesDrops=0, LldpStatsRemTablesAgeouts=0)     
复制代码


查看 Trap 缓冲区的前 10 条记录信息。


<Huawei> display trapbuffer size 10Trapping buffer configuration and contents: enabled                             Allowed max buffer size: 1024                                                   Actual buffer size: 256                                                         Channel number: 3, Channel name: trapbuffer                                     Dropped messages: 0                                                             Overwritten messages: 600                                                       Current messages: 256                                                                                                                                           #May  7 2012 15:12:40+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 15:07:35+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 15:02:19+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.217.150 exceeds the speed-limit value 5.                                                   #May  7 2012 14:56:55+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 14:51:40+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 14:46:35+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 14:41:06+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.217.62 exceeds the speed-limit value 5.                                                    #May  7 2012 14:35:54+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 14:29:54+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.                                                     #May  7 2012 14:24:39+00:00 Huawei SECE/4/ARP_SIP_SPEEDLIMIT_ALARM:OID=1.3.6.1.4.1.2011.5.25.165.2.2.2.11 The arp packet speed with source ip 10.137.216.1 exceeds the speed-limit value 5.       
复制代码


info-center channel

命令功能

info-center channel 命令用来配置信息输出时所使用的信息通道。


undo info-center channel 命令用来恢复信息输出时所使用的信息通道为缺省值。


缺省情况下,系统向各个方向输出信息所使用的信息通道如下表所示:


命令格式

info-center { console | logbuffer | logfile | monitor | snmp | trapbuffer } channel { channel-number | channel-name }
undo info-center { console | logbuffer | logfile | monitor | snmp | trapbuffer } channel
复制代码

使用实例

配置向控制台输出信息的通道。


<Huawei> system-view[Huawei] info-center console channel console
复制代码


配置向 Log 缓冲区输出信息的通道。


<Huawei> system-view[Huawei] info-center logbuffer channel logbuffer
复制代码


配置向日志文件输出信息的通道。


<Huawei> system-view[Huawei] info-center logfile channel 9
复制代码


配置向用户终端输出信息的通道。


<Huawei> system-view[Huawei] info-center monitor channel monitor
复制代码


配置向 SNMP 代理输出信息的通道。


<Huawei> system-view[Huawei] info-center snmp channel 5
复制代码


配置向 Trap 缓冲区输出信息的通道。


<Huawei> system-view[Huawei] info-center trapbuffer channel trapbuffer
复制代码

info-center channel name

命令功能

info-center channel name 命令用来为指定编号的信息通道命名。


undo info-center channel 命令用来恢复缺省的通道名。


缺省情况下,各信息通道的名称如下表:


命令格式

info-center channel channel-number name channel-name
undo info-center channel channel-number
复制代码

使用实例

将 0 号通道命名为 execconsole。


<Huawei> system-view[Huawei] info-center channel 0 name execconsole
复制代码

info-center enable

命令功能

info-center enable 命令用来使能信息中心功能。


undo info-center enable 命令用来去使能信息中心功能。


缺省情况下,信息中心功能处于使能状态。

命令格式

info-center enable
undo info-center enable
复制代码

使用实例

使能信息中心功能。


<Huawei> system-view[Huawei] info-center enableInfo: Information center is enabled. 
复制代码

info-center filter-id

命令功能

info-center filter-id 用来配置对指定的 Log 或 Trap 信息进行过滤的功能。


undo info-center filter-id 用来取消对指定的 Log 或 Trap 信息进行过滤的功能。


缺省情况下,不对任何 Log 或 Trap 信息进行过滤。

命令格式

info-center filter-id { id | bymodule-alias modname alias } * &<1-50>
undo info-center filter-id { all | { id | bymodule-alias modname alias } * &<1-50> }
复制代码

使用实例

配置对 ID 为 1098731530 的日志进行过滤。


<Huawei> system-view[Huawei] info-center filter-id 1098731530Info: Succeeded in appending log ID 1098731530.
复制代码


配置通过模块名和助记符进行过滤。


<Huawei> system-view[Huawei] info-center filter-id bymodule-alias CMD CLKCHGREBOOTCANCELED Info: Succeeded in appending log ID 3225948163.
复制代码


配置取消所有日志的过滤。


<Huawei> system-view[Huawei] undo info-center filter-id allInfo: Succeeded in deleting all IDs.  
复制代码

info-center logbuffer

命令功能

info-center logbuffer 命令用来使能 Log 信息向 Log 缓冲区的发送功能。


undo info-center logbuffer 命令用来去使能 Log 信息向 Log 缓冲区的发送功能。


缺省情况下,Log 信息向 Log 缓冲区的发送功能处于使能状态。

命令格式

info-center logbuffer
undo info-center logbuffer
复制代码

使用实例

使能 Log 信息向 Log 缓冲区的发送功能


<Huawei> system-view[Huawei] info-center logbuffer
复制代码

info-center logbuffer size

命令功能

info-center logbuffer size 命令用来配置 Log 缓冲区可容纳 Log 信息的条数。


undo info-center logbuffer size 命令用来恢复 Log 缓冲区可容纳 Log 信息的条数为缺省值。


缺省情况下,Log 缓冲区可容纳日志信息的数目为 512 条。

命令格式

info-center logbuffer size logbuffer-size [ channel { channel-number | channel-name } ]
undo info-center logbuffer size
复制代码

使用实例

配置 Log 缓冲区可容纳 Log 信息的条数的大小为 50。


<Huawei> system-view[Huawei] info-center logbuffer size 50
复制代码

info-center logfile path

命令功能

info-center logfile path 命令用来配置日志文件保存的路径。


undo info-center logfile path 命令用来取消配置的日志文件保存路径。

命令格式

info-center logfile path path
undo info-center logfile path
复制代码

使用实例

配置日志文件保存到 U 盘中。


<Huawei> system-view[Huawei] info-center logfile path usb0:/logfile
复制代码

info-center logfile size

命令功能

info-center logfile size 命令用来配置日志文件的大小。


undo info-center logfile size 命令用来恢复日志文件的大小为缺省值。


缺省情况下,日志文件的大小为 8M。

命令格式

info-center logfile size size
undo info-center logfile size
复制代码

使用实例

配置日志文件的大小为 32M。


<Huawei> system-view[Huawei] info-center logfile size 32
复制代码

info-center loghost

命令功能

info-center loghost 命令用来配置向日志主机输出信息。


undo info-center loghost 命令用来取消向日志主机输出信息。


缺省情况下,不向日志主机输出信息。

命令格式

info-center loghost ip-address [ channel { channel-number | channel-name } | facility local-number | language language-name | transport { udp | tcp ssl-policy policy-name } | { vpn-instance vpn-instance-name | public-net } | local-time | port port-id ] *
info-center loghost ipv6 ipv6-address [ channel { channel-number | channel-name } | facility local-number | language language-name | transport { udp | tcp ssl-policy policy-name } | local-time | port port-id ] *
undo info-center loghost ip-address [ vpn-instance vpn-instance-name ]
undo info-center loghost ipv6 ipv6-address
复制代码

使用实例

配置设备向 IPv4 地址为 10.1.1.1,端口为 6514 的日志主机发送信息,所使用的通道为 channel6。


<Huawei> system-view[Huawei] info-center loghost 10.1.1.1 port 6514 channel channel6 
复制代码


配置设备向 IPv6 地址为 FC00:0:0:3001::1 的日志主机发送信息。


<Huawei> system-view[Huawei] info-center loghost ipv6 fc00:0:0:3001::1
复制代码


配置设备向 IPv4 地址为 192.168.2.2 和 VPN 实例名为 vpn1 的私网内的主机发送信息。


<Huawei> system-view[Huawei] info-center loghost 192.168.2.2 vpn-instance vpn1
复制代码


配置设备向 IPv4 地址为 192.168.2.2 的日志主机发送信息。信息采用 TCP 模式进行传输,通过 SSL 策略进行加密,引用的已创建好的 SSL 策略名称是 huawei123。


<Huawei> system-view[Huawei] info-center loghost 192.168.2.2 transport tcp ssl-policy huawei123
复制代码

info-center loghost source

命令功能

info-center loghost source 命令用来配置设备向日志主机发送消息的源接口信息。


undo info-center loghost source 命令用来恢复设备向日志主机发送消息的源接口信息为缺省值。


缺省情况下,设备向日志主机发送信息的源接口就是实际发送信息的接口。

命令格式

info-center loghost source interface-type interface-number
undo info-center loghost source
复制代码

使用实例

将接口 Loopback0 的 IP 地址作为日志消息报文的源地址。


<Huawei> system-view[Huawei] interface loopback 0[Huawei-LoopBack0] ip address 10.1.1.1 255.255.255.0[Huawei-LoopBack0] quit[Huawei] info-center loghost source loopback 0
复制代码

info-center max-logfile-number

命令功能

info-center max-logfile-number 用来配置日志文件的最大保存个数。


undo info-center max-logfile-number 用来恢复日志文件的最大保存个数为缺省值。


缺省情况下,日志文件的最大保存个数为 200。

命令格式

info-center max-logfile-number filenumbers
undo info-center max-logfile-number
复制代码

使用实例

设置保存的日志文件个数为 100。


<Huawei> system-view[Huawei] info-center max-logfile-number 100
复制代码

info-center rate-limit except

命令功能

info-center rate-limit except 命令用来配置日志不受信息中心日志抑制。


undo info-center rate-limit except 命令用来删除此配置。

命令格式

info-center rate-limit except { byinfoid infoID | bymodule-alias modname alias }
undo info-center rate-limit except { byinfoid infoID | bymodule-alias modname alias }
复制代码

使用实例

配置通过模块名和助记符方式设置单条日志不受速率抑制。


<Huawei> system-view[Huawei] info-center rate-limit except bymodule-alias AAA AUTHEN_ERR_EVENT
复制代码


配置通过日志 ID 方式设置单条日志的不受速率抑制。


<Huawei> system-view[Huawei] info-center rate-limit except byinfoid ff5ad009
复制代码


配置取消单条日志的不受速率抑制。


<Huawei> system-view[Huawei] undo info-center rate-limit except bymodule-alias AAA AUTHEN_ERR_EVENT
复制代码

info-center rate-limit global-threshold

命令功能

info-center rate-limit global-threshold 命令用来设置信息中心每秒处理日志的总数。


undo info-center rate-limit global-threshold 命令用来恢复为缺省值。


缺省情况下,信息中心每秒钟最多处理 400 条日志信息。

命令格式

info-center rate-limit global-threshold value
undo info-center rate-limit global-threshold
复制代码

使用实例

配置信息中心每秒处理报文总数为 300。


<Huawei> system-view[Huawei] info-center rate-limit global-threshold 300
复制代码

info-center rate-limit monitor-period

命令功能

info-center rate-limit monitor-period 命令用来配置信息中心进行速率抑制的监控周期。


undo info-center rate-limit monitor-period 命令用来恢复缺省值。


缺省情况下,监控周期是 3 秒。

命令格式

info-center rate-limit monitor-period value
undo info-center rate-limit monitor-period
复制代码

使用实例

配置信息中心速率抑制的监控周期为 5 秒。


<Huawei> system-view[Huawei] info-center rate-limit monitor-period 5
复制代码

info-center rate-limit threshold

命令功能

info-center rate-limit threshold 命令用来配置信息中心每秒处理相同 ID 日志的阈值。


undo info-center rate-limit threshold 命令用来恢复为缺省值。


缺省情况下,信息中心每秒处理相同 ID 日志的阈值为 30 条。

命令格式

info-center rate-limit threshold value [ byinfoid infoID | bymodule-alias modname alias ]
undo info-center rate-limit threshold [ value ] [ byinfoid infoID | bymodule-alias modname alias ]
复制代码

使用实例

配置日志速率抑制的阈值为每秒 60 条。


<Huawei> system-view[Huawei] info-center rate-limit threshold 60
复制代码


配置通过模块名和助记符方式设置单条日志的速率抑制阈值为每秒 30 条。


<Huawei> system-view[Huawei] info-center rate-limit threshold 30 bymodule-alias AAA AUTHEN_ERR_EVENT
复制代码


配置通过日志 ID 方式设置单条日志的速率抑制阈值为每秒 20 条。


<Huawei> system-view[Huawei] info-center rate-limit threshold 20 byinfoid ff5ad009
复制代码


配置恢复系统监控阈值的默认值。


<Huawei> system-view[Huawei] undo info-center rate-limit threshold
复制代码


配置取消单条日志的速率抑制阈值。


<Huawei> system-view[Huawei] undo info-center rate-limit threshold bymodule-alias AAA AUTHEN_ERR_EVENT
复制代码

info-center source channel

命令功能

info-center source channel 命令用来配置向信息通道输出信息的规则。


undo info-center source channel 命令用来恢复信息通道输出信息的规则为缺省值。


缺省情况下,不同类别的信息向信息通道输出的规则如下:


命令格式

info-center source { module-name | default } channel { channel-number | channel-name } [ log { state { off | on } | level severity } * | trap { state { off | on } | level severity } * | debug { state { off | on } | level severity } * ] *
undo info-center source { module-name | default } channel { channel-number | channel-name }
复制代码

使用实例

将 SNMP agent 通道中的 CFM 模块的 Log 信息打开,且允许输出信息的最低级别为 warning。


<Huawei> system-view[Huawei] info-center source CFM channel snmpagent log level warning
复制代码

info-center statistic-suppress enable

命令功能

info-center statistic-suppress enable 命令用来使能连续重复日志的统计抑制功能。


undo info-center statistic-suppress enable 命令用来去使能连续重复日志的统计抑制功能。


缺省情况下,连续重复日志的统计抑制功能处于使能状态。

命令格式

info-center statistic-suppress enable
undo info-center statistic-suppress enable
复制代码

使用实例

配置关闭连续重复日志统计抑制功能。


<Huawei> system-view[Huawei] undo info-center statistic-suppress enable
复制代码

info-center timestamp

命令功能

info-center timestamp 命令用来配置输出的 Log、Trap 和 Debug 信息的时间戳格式。


undo info-center timestamp 命令用来恢复输出的 Log、Trap 和 Debug 信息的时间戳格式为缺省值。


缺省情况下,Log、Trap 和 Debug 信息采用的时间戳格式为 date。调试信息的时间精度为毫秒级,告警信息、日志信息的时间精度为秒级。

命令格式

info-center timestamp debugging { { date | short-date | format-date } [ precision-time { tenth-second | second } ] | boot | none}
info-center timestamp log { { date | short-date | format-date } [ precision-time { tenth-second | millisecond } ] | boot | none}
info-center timestamp trap { { date | short-date | format-date } [ precision-time { tenth-second | millisecond } ] | boot | none}
undo info-center timestamp { debugging | trap | log }
复制代码

使用实例

配置 Trap 信息时间戳格式为 boot。


<Huawei> system-view[Huawei] info-center timestamp trap boot
复制代码


配置 Log 信息、Trap 信息、Debug 信息的时间戳精度。


<Huawei> system-view[Huawei] info-center timestamp log date precision-time millisecond[Huawei] info-center timestamp debugging date precision-time tenth-second[Huawei] info-center timestamp trap date precision-time millisecond
复制代码

info-center trapbuffer

命令功能

info-center trapbuffer 命令用来使能 Trap 信息向 Trap 缓冲区的发送功能。


undo info-center trapbuffer 命令用来去使能 Trap 信息向 Trap 缓冲区的发送功能。


缺省情况下,Trap 信息向 Trap 缓冲区的发送功能处于使能状态。

命令格式

info-center trapbuffer
undo info-center trapbuffer
复制代码

使用实例

使能 Trap 信息向 Trap 缓冲区的发送功能。


<Huawei> system-view[Huawei] info-center trapbuffer
复制代码

info-center trapbuffer size

命令功能

info-center trapbuffer size 命令用来配置 Trap 缓冲区可容纳 Trap 信息的条数。


undo info-center trapbuffer size 命令用来配置 Trap 缓冲区可容纳 Trap 信息的条数为缺省值。


缺省情况下,Trap 缓冲区可容纳 Trap 信息的条数为 256 条。

命令格式

info-center trapbuffer size trapbuffer-size [ channel { channel-number | channel-name } ]
undo info-center trapbuffer size
复制代码

使用实例

配置 Trap 缓冲区可容纳 Trap 信息的条数为 30。


<Huawei> system-view[Huawei] info-center trapbuffer size 30
复制代码

reset info-center statistics

命令功能

reset info-center statistics 命令用来清除各模块的信息统计数据。

命令格式

reset info-center statistics
复制代码

使用实例

清除各个模块的信息统计数据。


<Huawei> reset info-center statistics
复制代码

reset logbuffer

命令功能

reset logbuffer 命令用来清除 Log 缓冲区中的日志信息。

命令格式

reset logbuffer
复制代码

使用实例

清除 Log 缓冲区中的信息。


<Huawei> reset logbufferWarning: This command will reset the log buffer. Logs in the buffer will be lost. Continue? (y/n)[n]:y
复制代码

reset trapbuffer

命令功能

reset trapbuffer 命令用来清除 Trap 缓冲区中的 Trap 信息。

命令格式

reset trapbuffer
复制代码

使用实例

清除 Trap 缓冲区中的信息。


<Huawei> reset trapbuffer
复制代码

save logfile

命令功能

save logfile 用来把日志文件缓冲区中的日志保存到日志文件中。

命令格式

save logfile
复制代码

使用实例

保存日志文件缓冲区中的信息到日志文件。


<Huawei> save logfileInfo: It may take several seconds,please wait...  Save log file successfully.
复制代码

terminal debugging

命令功能

terminal debugging 命令用来使能终端显示 Debug 信息功能。


undo terminal debugging 命令用来去使能终端显示 Debug 信息功能。


缺省情况下,终端显示 Debug 信息功能处于未使能状态。

命令格式

terminal debugging
undo terminal debugging
复制代码

使用实例

使能终端显示 Debug 信息功能。


<Huawei> terminal debuggingInfo: Current terminal debugging is on.
复制代码

terminal logging

命令功能

terminal logging 命令用来使能终端显示 Log 信息功能。


undo terminal logging 命令用来去使能终端显示 Log 信息功能。


缺省情况下,终端显示 Log 信息功能处于使能状态。

命令格式

terminal logging
undo terminal logging
复制代码

使用实例

去使能终端日志显示功能。


<Huawei> undo terminal loggingInfo: Current terminal logging is off.
复制代码

terminal monitor

命令功能

terminal monitor 命令用来使能终端显示信息中心发送信息的功能。


undo terminal monitor 命令用来去使能终端显示信息中心发送信息的功能。


缺省情况下,控制台显示功能处于使能状态,用户终端显示功能处于未使能状态。

命令格式

terminal monitor
undo terminal monitor
复制代码

使用实例

去使能终端显示功能。


<Huawei> undo terminal monitorInfo: Current terminal monitor is off.
复制代码

terminal trapping

命令功能

terminal trapping 命令用来使能终端显示 Trap 信息功能。


undo terminal trapping 命令用来去使能终端显示 Trap 信息功能。


缺省情况下,终端显示 Trap 信息功能处于使能状态。

命令格式

terminal trapping
undo terminal trapping
复制代码

使用实例

去使能 Trap 信息显示功能。


<Huawei> undo terminal trappingInfo: Current terminal trapping is off. 
复制代码


发布于: 3 小时前阅读数: 5
用户头像

Ethereal

关注

还未添加个人签名 2020.11.18 加入

还未添加个人简介

评论

发布
暂无评论
全网最牛逼的华为信息中心配置命令,建议收藏!